TSE0108-Leng紅外溫度傳感器（英文）
聲明：您必須遵守我們的協議，如果您下載了該資源行為將被視為對《電天下賬號管理規范》全部內容的認可，本網站資源來自原創，僅供用于學習和交流，請勿用于商業用途。如有侵權、不妥之處，請舉報本資源，我們將及時審核處理！
TSE0108-Leng紅外溫度傳感器（英文）
文本預覽
Page 1 of 7
SPECIFICATION
of
THERMOPILE
INFRARED SENSOR
UNIT
TSE 01/08 L
PART NO. : Rev. 1.0Page 2 of 7
1. SCOPE
This specification describes a Thermopile Infrared Sensor Unit for non-contact temperature measurement
2. TYPE of UNIT
2.1. TYPE NAME
Thermopile Infrared Sensor Unit
2.2. MODEL NO.
TSE 01/08 L
3. DIMENSIONS
See Fig. 1.
Production Lot No. is put on a Unit.
4. GENERAL CHARACTERISTICS
Table 1
PARAMETER STANDARD
4.1. Thermopile Sensor 8 Element Linear Array Unit Thermopile
(3 Digital Address Signal Inputs, Built-in 8ch Analog Multiplexer)
4.2. Optics Silicon Lens
4.3. Outputs Thermopile Signal Output (for Incident Infrared Energy Detection)
Thermistor Signal Output (for Ambient Temp. Detection)
(*) Both analog outputs are supplied individually.
4.4. Time Constant Max.30msec.
4.5. Circuit Configuration See Fig. 2
4.6. Detection Area See Fig. 3
4.7. Crosstalk See Fig. 4
4.8. Detecting Temperature Range -20 ~ 100 deg Celsius
4.9. Accuracy 1 Within (+/-) 2 deg Celsius (Open)
Accuracy 2 Within (+/-) 1 deg Celsius
(Heat Source 60
PART NO. : Rev. 1.0
(cid:0)
80 deg Celsius)
4.10. Operating Temperature 0 ~ 70 deg Celsius
4.11. Storage Temperature -20 ~ 90 deg Celsius
4.12. EEPROM 128w*8bit,1kb Serial Interface 2-Wire
(*) For Calibration Data InputPage 3 of 7
5. ELECTRICAL CHARACTERISTICS
Table 2
PARAMETER CONDITION STANDARD
5.1 Thermopile Signal Output Object Temp. : 72 deg Celsius 2.40 V (+/-) 1.2 %
Ambient Temp. : 20 deg Celsius (After each element
Distance : 250 mm correcte)
5.2 Temperature Characteristics of Object Temp. : -20 ~ 100 deg Celsius See Data 1
Thermopile Signal Output (Ambient Temp. : 10 ~ 50 deg Celsius)
When Ambient Temp. 70 deg Celsius,
Object Temp. : 20 ~ 100 deg Celsius
5.3 T h e r m i s to r Signal Output Ambient Temp. : 20 degrees Celsius 0.484 V (+/-) 3 %
5.4 Temperature Characteristics of Ambient Temp. : 10 ~ 50 deg Celsius See Data 2
Thermistor Signal Output
5.5 Reference Voltage 25 deg Celsius 1.225 V (+/-) 25%
5.6 Supply Voltage Single Power Supply 5 V DC
(Maximum Rating
: 5.25 V DC)
5.7 Current Consumption +Vs = 5 V Supply Max. 5 mA
5.8 Output Current Short Circuit to Ground Max. 60 mA
6. MEASUREMENT METHOD
6.1. Thermopile Signal Output
See Fig. 5.
7. NOTES
7.1. Design restrictions/precautions
For outdoor applications, be sure to apply suitable supplementary optical filter, drip-proof and
anti-dew construction. This Unit is designed for indoor use.
In cases where secondary accidents due to operation failure or malfunctions can be anticipated,
add a fail safe function to the design.
7.2. Usage restrictions/precautions
To prevent Unit malfunctions, operational failure or any deterioration of its characteristics, do not
use this Unit in the following, or similar, conditions.
7.2.1 Use in rapid environmental temperature changes.
7.2.2 Use in strong shock or vibration.
7.2.3 Use under the condition where there are obstructing materials (Glass, Fog, etc.) through which
infrared rays cannot pass within detection area.
7.2.4 Use in fluid, corrosive gases and sea breeze.
7.2.5 Continual use in high humidity atmosphere.
7.2.6 Use in field of static electricity or strong electromagnetic waves.
7.2.7 Use under the condition exposed to direct wind from a heater or air conditioner.
7.3. Handling and storage restrictions/precautions
To prevent Unit malfunctions, operational failure, appearance damage or any deterioration of its
characteristics, do not expose this Unit to the following or similar, handling and storage conditions.
7.3.1. Vibration for a long time.
7.3.2. Strong shock.
7.3.3. Static electricity or strong electromagnetic waves.
7.3.4. High or Low temperature and humidity for a long time.
7.3.5. Corrosive gases or sea breeze.
7.3.6. Dirty and dusty environments that may contaminate the optical window.
PART NO. : Rev. 1.0Page 4 of 7
Unit troubles resulting from misuse, inappropriate handling or storage are not the manufacturer’s
responsibility.
PART NO. : Rev. 1.0
(cid:1) (cid:2)(cid:4)
(cid:11)
(cid:3)(cid:6)
(cid:7)(cid:12)(cid:13) (cid:9)(cid:6)
(cid:5)(cid:8)
(cid:5)(cid:8)
SPECIFICATION
of
THERMOPILE
INFRARED SENSOR
UNIT
TSE 01/08 L
PART NO. : Rev. 1.0Page 2 of 7
1. SCOPE
This specification describes a Thermopile Infrared Sensor Unit for non-contact temperature measurement
2. TYPE of UNIT
2.1. TYPE NAME
Thermopile Infrared Sensor Unit
2.2. MODEL NO.
TSE 01/08 L
3. DIMENSIONS
See Fig. 1.
Production Lot No. is put on a Unit.
4. GENERAL CHARACTERISTICS
Table 1
PARAMETER STANDARD
4.1. Thermopile Sensor 8 Element Linear Array Unit Thermopile
(3 Digital Address Signal Inputs, Built-in 8ch Analog Multiplexer)
4.2. Optics Silicon Lens
4.3. Outputs Thermopile Signal Output (for Incident Infrared Energy Detection)
Thermistor Signal Output (for Ambient Temp. Detection)
(*) Both analog outputs are supplied individually.
4.4. Time Constant Max.30msec.
4.5. Circuit Configuration See Fig. 2
4.6. Detection Area See Fig. 3
4.7. Crosstalk See Fig. 4
4.8. Detecting Temperature Range -20 ~ 100 deg Celsius
4.9. Accuracy 1 Within (+/-) 2 deg Celsius (Open)
Accuracy 2 Within (+/-) 1 deg Celsius
(Heat Source 60
PART NO. : Rev. 1.0
(cid:0)
80 deg Celsius)
4.10. Operating Temperature 0 ~ 70 deg Celsius
4.11. Storage Temperature -20 ~ 90 deg Celsius
4.12. EEPROM 128w*8bit,1kb Serial Interface 2-Wire
(*) For Calibration Data InputPage 3 of 7
5. ELECTRICAL CHARACTERISTICS
Table 2
PARAMETER CONDITION STANDARD
5.1 Thermopile Signal Output Object Temp. : 72 deg Celsius 2.40 V (+/-) 1.2 %
Ambient Temp. : 20 deg Celsius (After each element
Distance : 250 mm correcte)
5.2 Temperature Characteristics of Object Temp. : -20 ~ 100 deg Celsius See Data 1
Thermopile Signal Output (Ambient Temp. : 10 ~ 50 deg Celsius)
When Ambient Temp. 70 deg Celsius,
Object Temp. : 20 ~ 100 deg Celsius
5.3 T h e r m i s to r Signal Output Ambient Temp. : 20 degrees Celsius 0.484 V (+/-) 3 %
5.4 Temperature Characteristics of Ambient Temp. : 10 ~ 50 deg Celsius See Data 2
Thermistor Signal Output
5.5 Reference Voltage 25 deg Celsius 1.225 V (+/-) 25%
5.6 Supply Voltage Single Power Supply 5 V DC
(Maximum Rating
: 5.25 V DC)
5.7 Current Consumption +Vs = 5 V Supply Max. 5 mA
5.8 Output Current Short Circuit to Ground Max. 60 mA
6. MEASUREMENT METHOD
6.1. Thermopile Signal Output
See Fig. 5.
7. NOTES
7.1. Design restrictions/precautions
For outdoor applications, be sure to apply suitable supplementary optical filter, drip-proof and
anti-dew construction. This Unit is designed for indoor use.
In cases where secondary accidents due to operation failure or malfunctions can be anticipated,
add a fail safe function to the design.
7.2. Usage restrictions/precautions
To prevent Unit malfunctions, operational failure or any deterioration of its characteristics, do not
use this Unit in the following, or similar, conditions.
7.2.1 Use in rapid environmental temperature changes.
7.2.2 Use in strong shock or vibration.
7.2.3 Use under the condition where there are obstructing materials (Glass, Fog, etc.) through which
infrared rays cannot pass within detection area.
7.2.4 Use in fluid, corrosive gases and sea breeze.
7.2.5 Continual use in high humidity atmosphere.
7.2.6 Use in field of static electricity or strong electromagnetic waves.
7.2.7 Use under the condition exposed to direct wind from a heater or air conditioner.
7.3. Handling and storage restrictions/precautions
To prevent Unit malfunctions, operational failure, appearance damage or any deterioration of its
characteristics, do not expose this Unit to the following or similar, handling and storage conditions.
7.3.1. Vibration for a long time.
7.3.2. Strong shock.
7.3.3. Static electricity or strong electromagnetic waves.
7.3.4. High or Low temperature and humidity for a long time.
7.3.5. Corrosive gases or sea breeze.
7.3.6. Dirty and dusty environments that may contaminate the optical window.
PART NO. : Rev. 1.0Page 4 of 7
Unit troubles resulting from misuse, inappropriate handling or storage are not the manufacturer’s
responsibility.
PART NO. : Rev. 1.0
(cid:1) (cid:2)(cid:4)
(cid:11)
(cid:3)(cid:6)
(cid:7)(cid:12)(cid:13) (cid:9)(cid:6)
(cid:5)(cid:8)
(cid:5)(cid:8)
AIGC產品名稱：TSE0108-Leng紅外溫度傳感器
解釋與描述：
TSE0108-Leng是一款專門設計用于非接觸式測量物體表面溫度的紅外線測溫設備。作為一款高性能的紅外溫度傳感器，它采用先進的紅外熱成像技術，能夠快速準確地捕捉并分析目標物體發出的紅外輻射能量，從而計算出其實際表面溫度。
此型號傳感器具有以下特點：
- **高精度**：通過優化的光子探測器和信號處理算法，提供精確到±2°C或更好的溫度讀數范圍，適用于多種工業、科研及日常生活中對溫度監控有要求的應用場景。
- **遠程非接觸**：用戶無需直接接觸被測物體，避免了由于物理接觸帶來的誤差和潛在的安全風險。
- **寬量程適應性**：該傳感器支持廣泛的溫度范圍，一般適用于-40℃至+150℃之間的環境，可根據具體需求進行定制設置。
- **小型輕便**：緊湊的設計便于集成在各類設備中，如智能家居系統、生產設備監測、環境監控等領域。
綜上所述，TSE0108-Leng紅外溫度傳感器是一款高效、便捷且可靠的溫度測量工具，能滿足不同領域?qū)τ诰_、實時溫度監測的需求。如果您有關于這款產品的更多問題或需要技術支持，請隨時聯系我們的客戶服務團隊。
相關資源推薦
