Danger
This symbol indicates the presence of dangerous voltage within and outside the product enclosure that
may constitute a risk of electric shock, serious injury or death to persons if proper precautions are not
followed.
Caution
This symbol alerts the user to the presence of hazards that may cause minor or moderate injury to
persons, damage to property or damage to the device itself, if proper precautions are not followed.
Note
This symbol directs the user’s attention to important installation, operating and maintenance instructions.
Installation Considerations
Installation and maintenance of the ION 8000 series meter should only be performed by qualified, competent
personnel that have appropriate training and experience with high voltage and current devices. The meter must be
installed in accordance with all Local and National Electrical Codes.
DANGER
Failure to observe the following instructions may result in severe injury or death.
(cid:139)During normal operation of the ION 8000 series meter, hazardous voltages are present on its terminal
strips, and throughout the connected potential transformer (PT), current transformer (CT), digital (status)
input, control power and external I/O circuits. PT and CT secondary circuits are capable of generating
lethal voltages and currents with their primary circuit energized. Follow standard safety precautions while
performing any installation or service work (i.e. removing PT fuses, shorting CT secondaries, etc).
(cid:139)The terminal strips on the meter base should not be user-accessible after installation.
(cid:139)Do not use digital output devices for primary protection functions. These include applications where the
devices perform energy limiting functions or provide protection of people from injury. Do not use the ION
8000 series in situations where failure of the devices can cause injury or death, or cause sufficient energy
to be released that can start a fire. The meter can be used for secondary protection functions.
(cid:139)Do not HIPOT/Dielectric test the digital (status) inputs, digital outputs, or communications terminals. Refer
to the label on the ION 8000 series meter for the maximum voltage level the device can
withstand.
CAUTION
Observe the following instructions, or permanent damage to the meter may occur.
(cid:139)The ION 8000 series meter offers a range of hardware options that affect input ratings. The ION 8000
series meter’s serial number label lists all equipped options. Applying current levels incompatible with the
current inputs will permanently damage the meter. This document provides installation instructions appli-
cable to each hardware option.
(cid:139)The ION 8000 series meter’s chassis ground must be properly connected to the switchgear earth ground
for the noise and surge protection circuitry to function correctly. Failure to do so will void the warranty.
(cid:139)Terminal screw torque: Barrier-type (current, voltage, and relay terminal screws: 1.35 Nm (1.00 ft-lbf)
max. Captured-wire type (digital inputs/outputs, communications, power supply: 0.90 Nm
(0.66 ft.lbf) max.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
3The Ringer Equivalence Number (REN) for the ION 8000 series optional internal modem is 0.6. Connection to the
ION 8000 series internal modem should be made via an FCC Part 68 compliant telephone cord (not supplied). The
ION 8000 series cannot be used on a public coin phone service or party line services.
Network Compatibility Notice for the Internal Modem
The internal modem in meters equipped with this option is compatible with the telephone systems of most countries
in the world, with the exception of Australia and New Zealand. Use in some countries may require modification of the
internal modem’s initialization strings. If problems using the modem on your phone system occur, please contact
Power Measurement Technical Services
Standards Compliance
Limitation of Liability
Power Measurement Ltd. (“Power Measurement”) reserves the right to make changes in the device or its
specifications identified in this document without notice. Power Measurement advises customers to obtain the
latest version of the device specifications before placing orders to verify that the information being relied upon
by the customer is current.
Regardless of whether any remedy set forth herein fails of its essential purpose, except to the extent the following
limitation is prohibited by applicable law, Power Measurement shall not, in any event or under any legal claim
or theory (whether based on contract, indemnity, warranty, tort (including negligence and strict liability) or
otherwise), be liable to the original purchaser or any other person or entity for special, indirect, incidental,
punitive, liquidated, special or consequential damages whatsoever with respect to any purchased product,
including, without limitation, business interruption, loss of use, profit or revenue, even if Power Measurement has
been advised of the possibility of such damages. To the extent that a limitation or exclusion of consequential
damages are prohibited by applicable law, then Power Measurement’s liability shall be limited to twice the
amount of the relevant purchased product. Not to limit the foregoing, a) Power Measurement shall not be liable
for any claim (other than a claim solely for the breach of one of the above Warranties that is made in accordance
with the above described procedures) made by the original purchaser, its employees, agents, or contractors for
any loss, damage, or expense incurred due to, caused by, or related to any purchased product; and b) the above
Warranties are the original purchaser's exclusive remedy and Power Measurement hereby expressly disclaims all
other warranties, express or implied, including, without limitation, warranties of non-infringement and the
implied warranties of merchantability and fitness for a particular purpose.
These limited Warranties shall not apply to any product that has been subject to alteration, accident, misuse,
abuse, neglect or failure to exactly follow Power Measurement's instructions for operation and maintenance. Any
technical assistance provided by Power Measurement's personnel or representatives in system design shall be
deemed to be a proposal and not a recommendation. The responsibility for determining the feasibility of such
proposals rests with the original purchaser and should be tested by the original purchaser. It is the original
purchaser’s responsibility to determine the suitability of any product and associated documentation for its
purposes. The original purchaser acknowledges that 100% "up" time is not realizable because of possible
hardware or software defects. The original purchaser recognizes that such defects and failures may cause
inaccuracies or malfunctions. Only the terms expressed in these limited Warranties shall apply and no
distributor, corporation or other entity, individual or employee of Power Measurement or any other entity is
authorized to amend, modify or extend the Warranties in any way.
The information contained in this document is believed to be accurate at the time of publication, however, Power
Measurement assumes no responsibility for any errors which may appear here and reserves the right to make
changes without notice.
Power Measurement, ION, ION Enterprise, MeterM@il, WebMeter and “smart energy everywhere” are either
registered trademarks or trademarks of Power Measurement. All other trademarks are property of their respective
owners.
Covered by one or more of the following patents:
U.S. Patent No's 6825776, 6813571, 6798191, 6798190, 6792364, 6792337, 6751562, 6745138, 6737855,
6694270, 6687627, 6671654, 6671635, 6615147, 6611922, 6611773, 6563697, 6493644, 6397155,
6186842, 6185508, 6000034, 5995911, 5828576, 5736847, 5650936, D459259, D458863, D443541,
D439535, D435471, D432934, D429655, D429533, D427533.
4ION 8000 Series Models
Socket Meter
The socket meter is designed to fit into S-Base meter sockets and A-to-S Base

您好！關于關口計量ION8000系列的詳細操作手冊，這是一個專門針對ION8000系列電力關口計量設備的操作指南。這款產品可能包含了高級的電能計量、實時監控和數據管理功能，用于電力系統的輸配環節，確保電能質量和交易的準確性。 通常，操作手冊會包含以下內容： 1. **設備介紹**：產品的基本概述，包括型號、功能特性以及適用環境。 2. **安裝步驟**：指導用戶如何安全地安裝和定位設備。 3. **接線圖與接口說明**：詳細列出各個端口的功能和連接方式。 4. **開機與初始化**：如何正確啟動設備并進行初次設置。 5. **操作流程**：提供日常使用中的操作方法，如數據采集、設置參數、故障排查等。 6. **功能演示**：可能包含視頻教程或圖文示例，幫助用戶理解復雜功能。 7. **維護保養**：設備的清潔、檢查和定期維護建議。 8. **故障排除**：常見問題的解決方法和故障代碼解讀。 為了獲取最準確的信息，建議您直接查閱官方提供的操作手冊，或者聯系我們的技術支持團隊，他們可以提供專業的在線指導。如果您在閱讀過程中遇到任何疑問，也可以隨時告訴我，我會盡力幫助您解答。